Well it's getting closer, the desk that is. The door and drawer fronts have been kerffed to make them look like a bank of drawers. Something that I would have had the devil of a time doing on the table saw but was very straight forward not to mention upright with the Radial Arm Saw. The saw is mounted above the work on a radial arm so you can see what you are cutting. Unlike a table saw that cuts from the bottom. When you are just cutting a groove you are flying blind with a table saw.
I also constructed the wire box, a chase for the computer wiring that connects the pedestals. It has a hinged front and holes in either end to let you pass wires easily through. It also helps keep them up off the floor and out of sight also a great idea.
Right now I would be working on attaching the door and drawer fronts but the battery on the cordless drill conked out and the spare must have been put away dead too. Note to self "DON'T DO THAT!" So here I am waiting for the batteries to recharge. I have a drill with a cord but it is a big 1/2 inch and it doesn't fit in where I need to drill. Well it fits but you can't hold on to it when its in there. Also the charger is plugged in where I need to plug the drill in. I would unplug the freezer for a minute or two but then if I forgot to plug it back in I would have a lovely mess in a few days. And you know that "sometimers" (like Alzheimer's only less permanent and intermittent) would kick in right about then. You see the basement has never been finished and there is a distinct shortage of circuits. Since we never used to use the basement it was not a problem but it looks like it is something that I will have to rectify and soon if I want to keep using the basement as a workshop.
Guess I could take the dog for a walk while I wait.
Belle want to go for a walk? As if I couldn't guess...
Randy
Sunday, March 25, 2007
Thursday, March 22, 2007
Quick Note
Just a quick note today. I have not forgotten everyone its just that we have had company for the past week and I am only now getting back to the desk project.
My mother in law was in town for a couple of weeks and she stayed with us last week so we were kind of busy. She was in from Prince Albert Saskatchewan and arrived just in time to experience a full on Calgary Chinook. There was nearly a foot of snow lying around when she arrived and it was brown when she left. The one day it rained in the morning was warm and sunny in the afternoon and snowing at night. Calgary weather. If you don't like what you have wait 20 minutes.
I am back on the desk again. Just little things. Trim around the pedestals installed. Yesterday I made up the parts for the wire box that connects them. I'll put that together on the weekend along with finishing up the false drawer fronts and door and the keyboard drawer. Then all I will have left is the top to finish. The breadboard edge is making me nervous. I don't want to make any mistakes there. Keep your fingers crossed.
Still down in the basement...
Randy
My mother in law was in town for a couple of weeks and she stayed with us last week so we were kind of busy. She was in from Prince Albert Saskatchewan and arrived just in time to experience a full on Calgary Chinook. There was nearly a foot of snow lying around when she arrived and it was brown when she left. The one day it rained in the morning was warm and sunny in the afternoon and snowing at night. Calgary weather. If you don't like what you have wait 20 minutes.
I am back on the desk again. Just little things. Trim around the pedestals installed. Yesterday I made up the parts for the wire box that connects them. I'll put that together on the weekend along with finishing up the false drawer fronts and door and the keyboard drawer. Then all I will have left is the top to finish. The breadboard edge is making me nervous. I don't want to make any mistakes there. Keep your fingers crossed.
Still down in the basement...
Randy
Sunday, March 4, 2007
Why I did not write.
I've been away from the desk project and from posting for couple of weeks. We had a little excitement on the medical front this last week. My wife had a cancer test. And as it turned out she is fine. The doctor told her to come back in five years and they will check again. That means that she has by his estimate at least a 5 year shelf life. Where as I can't necessarily make that claim. She will out live me of that I am sure. Women live longer than men, any stand up comic will tell you, because after putting up with women men do not want to live any more. Bada-boom!
At any rate when we got through the test she is fine and off we go. The test took a year to schedule. That's right she booked it a full year ago. That is what they call the Alberta Heathcare Advantage. If there would have been a problem, by the time she got tested they could have found it in an autopsy. But one way or another they would have found it. The government's approach is that the autopsy is better because there are no repeat offenders and it frees up the hospital beds for those who are willing to pay. Conservative logic at its best. As you will have guessed I am no fan of our current right wing government. But what can we do when the majority elects a premier because he's a lush and that "makes him one of the guys!".
Enough politics.
I took a break from the desk just to get through the wife's test and because I was having a few problems that I had to resolve. They are done and now it is time to get back at it. The problems had to do with he trim for the pedestal base. I milled up the the stock I needed then when I went to mitre it one of the pieces chipped and there I was short of materiel. Then when I went to cut the "feet" my jig saw which was never a good one (I have had trouble with that thing since day one) failed me again. I may be the problem but I swear the tool hates me too. At any rate now I was short two pieces. I have purchased the stock again and I just have to re mill it. I also decided that I don't need to make the cut outs in the base trim as I found a system of adjustable feet that I can install under the pedestal if I need to later. The problem with the desk not sitting level will not be a problem because for now it will be set up on carpet which is self leveling more or less.
So now that I don't have to do anything fancy I am ready to start again except that this week was housekeeping. Cleaning the house took a half a day, we lost a day to the regular weekend errands and so it goes. Then there was another couple of hours going from one hardware store to another looking for stain and varathane, (Home Depot dropped the ball again being sold out of the stain I wanted, and only the color I wanted, so I went with their evil twin RONA). I don't even wonder any more why the progress is so slow I know that it is always two steps forward and one step back.
Finally when I went to write this post I could not get connected to the net. Telus was dropping the ball. I had to disconnect the whole system, modem, router, firewall and reconnect then it worked. It was not Telus's problem even though "they were experiencing a high volume of calls" . I guess when my router which regularly works fine decides to pack it in, it up and calls all it's buddies so everyone can have a router failure at the same time. I think that since the system started working on its own half way through Telus debugging the problem it must have been my equipment...NOT. It certainly would not have been their network. If you don't believe me just ask them.
Making less progress than I had intended...
Randy
At any rate when we got through the test she is fine and off we go. The test took a year to schedule. That's right she booked it a full year ago. That is what they call the Alberta Heathcare Advantage. If there would have been a problem, by the time she got tested they could have found it in an autopsy. But one way or another they would have found it. The government's approach is that the autopsy is better because there are no repeat offenders and it frees up the hospital beds for those who are willing to pay. Conservative logic at its best. As you will have guessed I am no fan of our current right wing government. But what can we do when the majority elects a premier because he's a lush and that "makes him one of the guys!".
Enough politics.
I took a break from the desk just to get through the wife's test and because I was having a few problems that I had to resolve. They are done and now it is time to get back at it. The problems had to do with he trim for the pedestal base. I milled up the the stock I needed then when I went to mitre it one of the pieces chipped and there I was short of materiel. Then when I went to cut the "feet" my jig saw which was never a good one (I have had trouble with that thing since day one) failed me again. I may be the problem but I swear the tool hates me too. At any rate now I was short two pieces. I have purchased the stock again and I just have to re mill it. I also decided that I don't need to make the cut outs in the base trim as I found a system of adjustable feet that I can install under the pedestal if I need to later. The problem with the desk not sitting level will not be a problem because for now it will be set up on carpet which is self leveling more or less.
So now that I don't have to do anything fancy I am ready to start again except that this week was housekeeping. Cleaning the house took a half a day, we lost a day to the regular weekend errands and so it goes. Then there was another couple of hours going from one hardware store to another looking for stain and varathane, (Home Depot dropped the ball again being sold out of the stain I wanted, and only the color I wanted, so I went with their evil twin RONA). I don't even wonder any more why the progress is so slow I know that it is always two steps forward and one step back.
Finally when I went to write this post I could not get connected to the net. Telus was dropping the ball. I had to disconnect the whole system, modem, router, firewall and reconnect then it worked. It was not Telus's problem even though "they were experiencing a high volume of calls" . I guess when my router which regularly works fine decides to pack it in, it up and calls all it's buddies so everyone can have a router failure at the same time. I think that since the system started working on its own half way through Telus debugging the problem it must have been my equipment...NOT. It certainly would not have been their network. If you don't believe me just ask them.
Making less progress than I had intended...
Randy
Sunday, February 18, 2007
Long Awaited Pictures
Well finally as promised some pictures of the desk. It is starting to resemble something...but what? I finished the basic pedestals this week so I thought I would set it up to get an idea of the size. Yes sir it come in on the huge side. Oh well.The pedestals are made of the mahogany frames and the birch panels. They look a lot lighter than the frame but they will take stain much more than the mahogany. The bottom and tops are plywood trimmed in mahogany at the top. The backs of the pedestals are open to allow heat to escape. When the old computer is slaving away over taxes it gets a little hot under the collar.
These are the drawers and shelves. I have to attach the slides and install them. There are 3 small shelves for the computer scanner and CD's a large drawer with attached shelf for the printer (paper storage underneath. And two large drawers for pens pencils and junk. I think they will become a fabulous junk repository . We already have a junk drawer but now we have room for expansion. Junk is like air it expands to fill the space available. Make more space and more junk will appear. 
There is not much left of the mahogany parts just the glued up doors shown here, the keyboard shelf and some trim pieces.
Not much to show for a van load of wood just over a month ago.
Not much to show for a van load of wood just over a month ago.
And in a few weeks there will be less than that
And here is one tired helper. She even brought her helper hat with her. But it is not for wearing it is for chewing on.
Still busy making sawdust...
Randy
Sunday, February 11, 2007
Thanks and No thanks
Still working on the desk, almost to the point where I have something worth taking a picture of. I have the panels for the pedestal sides done up and I made the drawers up today. I will post some pictures when I have the pedestals made up.
I took the desk top in to a wood working shop, Black Forest Woods. They took my rough top and trimmed it to size on their big industrial table saw. What took them 15 minutes would have been an all day chore for me with poorer results. They did a wonderful job. Thanks Black Forest. Check them out. They specialize in custom built doors, exotic hardwoods and wood working tools. http://www.blackforestwood.com
As it turned out the real all day chore was shopping around to find the drawer glides. There are two big name hardware chains in town, Rona and Home Depot. Both big impersonal box stores who amazingly sell exactly the same stuff for... wait for it... the same price, and as it turns out were sold out of the same things. I ended up going to three stores fighting traffic all the way only to come home still short of all the parts I needed. And because of the labor market here only one of the several staff members was knowledgeable. What we heard most was "Sorry I don't know I just started." You would think that they would have experienced staff in on the weekend when they are the busiest. But I guess they figure they have a captive audience. No thanks to Rona and Home depot you dropped the ball yesterday.
I got the rest of the parts cut out of the famous 5X5 sheets of plywood. I owe thanks on that to my friend Glenn who loaned me his out feed stands. I put one beside the table saw and the other on the out feed end. It was like having another pair of hands. Thanks Glenn.
And finally I got my father in law's radial arm saw up and working. There are a few things on this project that are just best done with a radial arm saw. He gave it to me three years ago and I had not got around to setting it up. But as I will be needing it it was time. And conveniently my nephew Robert was in town from Winnipeg visiting his cousin Scott. Since the saw originally belonged to their grandfather I asked them over to help set it up. It didn't hurt that they are both big guys, six foot or better, rugby and soccer players, so a little old saw was no challenge to them. We had it up in about a half an hour and adjusted just in time for some celebratory beers. (They are of legal age .) Well Robert had a couple and I had a couple and Scott had to drive so he lost out but I sent a couple home with him for later. Thanks Scott and Robert I appreciate the help and the visit.
And since I had a couple this afternoon I thought it might be a good idea to stay away from the power tools tonight thank you!
Ready to watch The New Yankee Workshop through the eyelids...
Randy
I took the desk top in to a wood working shop, Black Forest Woods. They took my rough top and trimmed it to size on their big industrial table saw. What took them 15 minutes would have been an all day chore for me with poorer results. They did a wonderful job. Thanks Black Forest. Check them out. They specialize in custom built doors, exotic hardwoods and wood working tools. http://www.blackforestwood.com
As it turned out the real all day chore was shopping around to find the drawer glides. There are two big name hardware chains in town, Rona and Home Depot. Both big impersonal box stores who amazingly sell exactly the same stuff for... wait for it... the same price, and as it turns out were sold out of the same things. I ended up going to three stores fighting traffic all the way only to come home still short of all the parts I needed. And because of the labor market here only one of the several staff members was knowledgeable. What we heard most was "Sorry I don't know I just started." You would think that they would have experienced staff in on the weekend when they are the busiest. But I guess they figure they have a captive audience. No thanks to Rona and Home depot you dropped the ball yesterday.
I got the rest of the parts cut out of the famous 5X5 sheets of plywood. I owe thanks on that to my friend Glenn who loaned me his out feed stands. I put one beside the table saw and the other on the out feed end. It was like having another pair of hands. Thanks Glenn.
And finally I got my father in law's radial arm saw up and working. There are a few things on this project that are just best done with a radial arm saw. He gave it to me three years ago and I had not got around to setting it up. But as I will be needing it it was time. And conveniently my nephew Robert was in town from Winnipeg visiting his cousin Scott. Since the saw originally belonged to their grandfather I asked them over to help set it up. It didn't hurt that they are both big guys, six foot or better, rugby and soccer players, so a little old saw was no challenge to them. We had it up in about a half an hour and adjusted just in time for some celebratory beers. (They are of legal age .) Well Robert had a couple and I had a couple and Scott had to drive so he lost out but I sent a couple home with him for later. Thanks Scott and Robert I appreciate the help and the visit.
And since I had a couple this afternoon I thought it might be a good idea to stay away from the power tools tonight thank you!
Ready to watch The New Yankee Workshop through the eyelids...
Randy
Subscribe to:
Posts (Atom)
